Pass-through seals - Vilpe

Show all products

Aerial Sleeve 12-100

Pass-through seal for a Ø 12/19/25/38/50/60/75/90/100 mm aerial pipe, mast, cable or roof bollard installed on a roof

Made of EPDM rubber; operating temperatures between -30 and +90°C

Pipe Sealing 110–155

Pass-through seal for a Ø 110-155 mm pipe, mast, cable or roof bollard installed on a roof

Made of EPDM rubber; operating temperatures between -30 and +90°C

Felt Roof Seal

Pass-through seal for round pipes installed on a felt roof

Made of EPDM rubber; operating temperatures between -30 and +90°C

Should be installed with hot bitumen between two felt layers

Clamp

Screw-on hot galvanized clamp for use with the VILPE® Felt Roof Seal

Should be selected based on the size of the seal and pipe

R-Felt Set

Pass-through seal for round pipes installed on a felt roof while retrofitting

Made of EPDM rubber; operating temperatures between -30 and +90°C

Should be installed with hot bitumen between two felt layers

RHS Seal

Pass-through seal for square pipes installed on a felt roof

Made of EPDM rubber; operating temperatures between -30 and +90°C

Should be installed with hot bitumen between two felt layers

RHS Clamp RST

Screw-on clamp for use with the VILPE® RHS Seal

Should be selected based on the size of the seal and pipe

Roof Seal Retrofitting Set

Pass-through seal for different kinds of pipes (e.g. mountings for billboards and flagpoles or electrical wires) installed on a metal roof while retrofitting

Made of EPDM rubber; operating temperatures between -30 and +90°C

Should be installed with hot bitumen between two felt layers

Roof Seal Set

Pass-through seal for different kinds of pipes (e.g. mountings for billboards and flagpoles or electrical wires) installed on a metal roof

Made of EPDM rubber; operating temperatures between -30 and +90°C

Should be installed with hot bitumen between two felt layers

Vapour Barrier Seal

Vapour barrier seal for pipes installed through the vapour barrier on an inclined or low-pitched roof (height 33 mm)

Made of EPDM rubber; operating temperatures between -30 and +90°C

Should be installed with bitumen if a roof's vapour barrier is made of bitumen, and with a board made of hard material on top of the vapour barrier valve if a roof's underlay material is made of profiled sheet metal

Tall Vapour Barrier Seal

Tall vapour barrier seal for pipes installed through the vapour barrier on an inclined or low-pitched roof (height 133 mm)

Made of EPDM rubber; operating temperatures between -30 and +90°C

Should be installed with bitumen if a roof's vapour barrier is made of bitumen, and with a board made of hard material on top of the vapour barrier valve if a roof's underlay material is made of profiled sheet metal

PVC Roof Seal

Pass-through seal for round pipes installed on a PVC roof

Made of coloured polyvinyl chloride (PVC)

Should be installed with hot air welding

RHS Clamp

Description: Hot-dip-galvanized clamp for fixing square VILPE RHS Seal. The clamp is chosen according to the pipe size. Contents: Two-piece clamp.

RHS-Felt Retrofitting Seal 80-150

Pass-through seal for square pipes installed on a felt roof while retrofitting

Made of EPDM rubber; operating temperatures between -30 and +90°C

Should be installed with hot bitumen between two felt layers

Roofseal

Description: Pass-through seal for different kinds of pipes (e.g. mountings for billboards and flagpoles or electrical wires) installed on a metal roof. The weather- and ozone-resistant properties of EPDM rubber are the best possible, and it can endure continuous heat stress of +90°C (and intermittently up to +150°C). EPDM rubber also tolerates the acids and alkalis often found in the air in industrial areas. Should be installed with hot bitumen between two felt layers. Pass-through seals are recommended to use on flat roofs (< 11,5° slope). Dimensions: Available in 6 different sizes with diameters 12-521 mm. Contents: Seal

XL Pipe sealing 175–250

For leading antennas, flagpoles and other pipes and bollards through the roof

Stepped EPDM rubber, installed on a separately available VILPE® XL pass-through

The pass-through is chosen according to the roofing material